Search Results

It is a well-known fact that the exhaust emission characteristics of hydrogen fueled engines are extremely good. The external mixture formation - a hydrogen fuel supply method - has the merit of practically zero NOx emission level in the lean mixture range with the excess air ratio λ set at 2.0 or greater as well as the merits of simple mechanism and easy operation. However, the practical use of such engines has been impeded partly due to the occurrence of backfire where the excess air ratio λ is 2 to 3. In order to allow the practical use of the hydrogen fueled engines with external mixture formation, it is vital to determine the causes of backfire and to establish proper countermeasures. It is found through a recent study conducted on the mechanism of backfire that the abnormal electric discharge in the intake stroke is one of the causes of backfire.

This study has been aimed at the reduction of the intense piston skirt friction force that appears in the expansion stroke out of all piston friction forces generated in gasoline engines. The friction characteristics at the piston skirt have been analyzed according to the measured results at piston friction forces and the shapes of wears at the piston skirt in actual engine operations. It is found from the above that the majority of the side force working on each piston is supported by the oil film on the skirt, while only some of the side force is supported by the portion in metallic contact with the cylinder. It is also found through experiments that the metallic contact portion has a great effect on the friction force at the skirt. The effect of piston posture in expansion stroke on the friction force has been also analyzed based on the measured results of piston slap motions.

The aim of this research was to analyze the lubrication conditions of piston pin boss bearings used in the press-fit piston pins of automobile gasoline engines. An original pin boss friction measuring device was developed and used to successfully obtain measurements. It was revealed that the friction force peaks twice every cycle at high engine loads, and non-fluid lubrication characteristics are displayed. The friction forces for various differing piston pins and pin boss bearings were analyzed, and it was shown that reducing piston pin length or thickness to reduce piston weight, or reducing the pin boss bearing clearance to reduce noise worsen the friction characteristics and increase the possibility of abnormal bearing friction as well as seizure.

In this study, the cause of backfire concerning an external mixture formation type hydrogen engine was clarified. It has been known that the maximum output power of the external mixture formation type hydrogen engine should be kept significantly low, because of backfire. Generally, the backfire of this type of hydrogen engine is caused by pre-ignition. In this type of hydrogen engine, pre-ignition occurred for a range of lean mixture. Under this study, therefore, the relationship between the occurrence of backfire and the temperature at the tip of the spark plug electrode, and the detection of the luminescence spectrum of the flame near the spark plug were examined and studied in relation to the spark plug ignition theory which appeared to be promising. Then the pre-ignition timing and location were studied by detecting the flame luminescence spectrum.

In order to establish hydrogen engines for practical use, it is important to overcome difficulties caused by unique characteristics of hydrogen fuel. A hydrogen engine with direct injection right before top dead center(TDC) and spark ignition has advantages such as prevention of abnormal combustion and realization of high power output near the stoichiometric air-fuel ratio, in comparison with an engine with external mixture. On the other hand, it has been pointed out that ignition and combustion for this type of hydrogen engines should be improved and that further studies on mixture formation of air and injected hydrogen are necessary for the improvement. For the direct injection hydrogen engine, mixture is formed both by air flow inside the combustion chamber and by injected hydrogen jet.

According to authors' previous research, high pressure hydrogen engines with direct injection right before TDC and spark ignition obtain high performance and eliminate almost. abnormal combustion. This study has clarified the mooted points in the flame propagation to adjacent jets and the control of the optimum spark timing and large NOx emissions even in leaner than excess air ratio of λ=2. Nitric oxides (NOx) is the only the pollutant in the exhaust gases emitted by hydrogen engines. It has been found that the NOx formation largely depends on the mixture formation method. In order to operate the engine in a small amount of NOx, an experimental study was carried out to investigate the reduction of NOx and the output power by using dual mixture formation method, external mixture formation and direct injection.

Considerable amount of research work on hydrogen fueled engines has been conducted for 17 years in Musashi Institute of Technology. The primary purpose of the research has been to develop a hydrogen powered autmobile, and in order to realized it, various innovations have been applied and tested. The newest outcome of this 17 years research was Musashi-7 Track, which demonstrated its performance in Innovation vehicle Design Competition held in Vancouver in July 1986. Musashi-7 Track was a modified medium duty truck, which was originally made by Hino Motors, and had a hydrogen powered engine. The track was equipped with 150 ℓ liquid hydrogen (LH2) tank and 8 MPa high pressure LH2 pump. The pump delivered 8 MPa high pressure hydrogen gas to the engine and the fuel was injected to a hot surface igniter in DI combustion chamber. This type of hydrogen enigne has following advantages. Firstly, fuel corrier weight and volume can be much smaller than those of metal-hydrides (MH).

In high pressure hydrogen injection hot surface ignition engines under nearly all engine operating conditions combustion pressure vibration is generated just after ignition. As a result of many experimental investigations the true nature for the cause of this interesting phenomenon was found and are listed: (1) This phenomenon probably originates from the extremely high local rate of burning of the hydrogen-air mixture. (2) Accompaning the stronger combustion pressure vibration was an increase in engine vibration and noise with increase in NOx emission and higher piston temperature. (3) Longer ignition delay resulted in a steeper pressure-time diagram which resalted in a stronger combustion pressure vibration. (4) The phenomenon had negligible effect on engine performance. (5) The phenomenon can be prevented by premixing a ceratain quantity of hydrogen gas into the intake air stream. The result was a shortened ignition delay.

A thin film thermocouple with a high accuracy was developed by means of computer analysis, which allowed measurements of instantaneous temperatures and heat fluxes on combustion chamber walls. Conventional Al-alloy and ceramic plates were compared in terms of the heat loss at the upper surface of each piston during combustion, using a gasoline engine and a diesel engine in the series of experiments. It was found by the comparison that the ceramic plates subjected to higher temperatures had greater heat losses in both the gasoline and diesel engines contrary to the anticipation.

The hydrogen combustion characteristics have been studied in a late-injection (near TDC) hot surface ignition engine. As a supplemental experiment, the mode of combustion was observed in a constant volume combustion chamber by the schlieren method. Consequently the combustion process, that was the flame propagation initiated by a hot surface through heterogeneous hydrogen jets, was not the same as that of a diesel engine. The experimental results in test engine showed the optimum number of injection holes and the effect of intake air swirl for better mixture formation. It was observed that the combustion was frequently accompanied by non-negligible combustion pressure vibrations at all engine operating conditions.